For the wide use of screen, the state has regulations. You also specify the diameter size, mesh size, or usage method. For plastering nets, the mesh should be less than 20 and the diameter should be greater than 1 mm. Not only are specifications specified, but safety is preferred if wire mesh is used in exterior plastering nets. If you fall, the consequences are unimaginable. Therefore, the application of norms should be combined with reality.
Wire mesh first welding after galvanized is through the end of welding and then cold this company to produce wire mesh wire mesh steel mesh construction mesh floor heating mesh galvanized or hot dip galvanized. First galvanized after welding is to change wire mesh, after the end of welding can see the solder joint; The two processes are different in price. The cost of plating after welding is low, the appearance is smooth, and the cost of plating after welding is high, and it is not easy to rust.
1. Eliminate caked zinc residue on zinc liquid surface
The second is according to the barbed wire material to determine the importance of the process, it is especially embodied in hot dip galvanized barbed wire, because of the different treatments of barbed wire in wire material and ductility have some discrepancy, if not pay attention to in the process it is easy to damage on the surface of zinc layer, directly affect the barbed wire rust resistance.
During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.
Construction welding net work wall insulation project using galvanized welding network in wall insulation and rust engineering project plays a necessary role, wall painting batch putty network is divided into two kinds: this is galvanized welding network; Another is to change the wire drawing wire welding mesh, according to the provisions of the region, construction enterprises to carry out effective material selection. Construction welded wire mesh new mink cage new mink cage grommet see more 1 inch, from silk in 2 mm up and down, management method is simple and easy, a mesh surface bright and clean and is not easy to scratch mink, galvanized welded wire online zinc quantity proportion, it is not easy to rust, new mink cage up more convenient, mink settled in natural environment more comfortable, the price also is higher than before the same specifications of the mink cage competitive many, But the overall character is not harmed at all, it is stronger.
Hexagonal net in the landslide value is also quite high, many slopes through the baptism of the rain after this, there may be sediment flow and other disasters to the people’s property lead to a certain loss, with the existence of the hexagonal net, can fundamentally go up to solve the problem, sediment flow when it comes to it can implement effective protection, is the loss of many people to low. The hook mesh was installed on the hillside, still a nice view line. Under the irradiation of the sun, the metal material of the hexagonal net shines brightly, and its beautiful shape is combined, giving the mountain a kind of elegant feeling.
In order to make the zinc content of steel wire stable in the future, and maintain its uniformity, as far as possible to reduce the zinc content, and effectively reduce zinc consumption to the actual work, the following measures are proposed by the wire factory:
2. Zinc layer uniformity: zinc layer uniformity also has an important impact on corrosion resistance. If the zinc layer is not uniform, there are local defects or insufficient thickness areas, it is easy to form corrosion points, resulting in the destruction of the entire zinc layer.There is as far as possible not to show the trace of the application of wire, wire wound flower stems should be wrapped with green or brown tape, in order to cover the trace of the use of wire, in the use of wire modeling can make the drooping flower head raised, and the flower head reinforcement, for herbs and other flower material soft plants, can make the stalk straight. Wire shearing method: if you want to cut the wire, the wire should be straightened and then cut, can not bend the wire, fold and then cut, otherwise, the wire cut is not straight, will bring a small hook, affect the use.
Blade thorn rope because the volume is relatively large, so the thorn rope factory is used to packaging.
Select cut silk first to ensure that the raw material of the silk is exactly the raw material you need, the raw material will be used well. Choose high straightness, so that the length of the truncation will be the same, will not show a lot of length difference, the length of the truncated wire is a very important element to choose the truncated wire.
Stainless steel barbed wire in the way of corrosion is not too, because the surface is not treated but relies on its own raw materials for corrosion resistance, so there will be no chemical reaction.
Compared with other galvanizing processes, galvanized steel wire has low cleaning requirements before plating. However, under the current trend of increasing the quality level of galvanized layer, some pollutants brought into the plating tank are obviously harmful. Because cleaning galvanized coating wastes a lot of time and reduces production, it is very important to properly clean and effectively rinse the substrate before electroplating.
2. The cleaning agent used for cleaning should have no effect on the binding force of the coating and no corrosion on the matrix.