Galvanized wire to galvanized uniform, a body is now its cross section, the second is the longitudinal uniformity. In the actual operation process, such as the jitter of steel wire, the surface of the pot scum and other reasons will cause galvanized wire surface galvanized layer accumulation, should try to solve the problem.
The life of the “wire”, is actually “low carbon steel wire”, carbon content in less than 0.2%. The surface is usually coated with zinc plating because it is easy to rust. Under atmospheric conditions, the galvanized layer will not rust before most of the fall off, relatively soft. The life of the “steel wire”, is carbon content in about 0.6% of the “carbon steel wire”, or carbon content in about 0.8% of the “high carbon steel wire”, they have enough hardness and elasticity after appropriate heat treatment, high strength. Uses such as winding ordinary spring and so on.
3, the barbed rope protective net in the bridge, channel, should be in the direction of the bridge cone slope (or end wall), should not leave people, animals can drill into the gap.Breeding cattle and sheep with thorn rope effect is still better, because the advantages of thorn rope are more. So is the effect of thorn rope used for livestock breeding good?
There are still some differences between electric mesh and wire mesh and steel mesh. This mesh is mainly a welding mesh made of high quality low carbon steel wire after straightening and cutting, and then welded by electric welding equipment. It can be said that because of the characteristics of fast production and convenient transportation, it has been applied in many industries. In today’s construction projects, people can also see the image of this network well. The application of welded mesh in this industry is mentioned because of its strong corrosion resistance and uniform mesh. It has become a special grid for floor heating in construction industry and has been applied in many fields.
The production process is to roll the hot metal billet into 5mm thick steel, and then put it into the wire drawing device, draw into different diameters of the line and gradually reduce the aperture of the wire drawing disk. Production process through cooling, annealing, coating and other processing technology, and then made into a variety of different specifications of galvanized wire. Galvanized wire production because of simple process, wide application, early development. Galvanized wire or steel wire is a cold working product of steel wire, and the material used is generally low carbon steel or stainless steel.
4, the material requirements of the silk: change wire braid, electric galvanized wire braid, hot galvanized wire braid, first braid after hot plating.Razor wire, also known as razor wire and razor net, is a new type of protective net. Blade barbed wire has beautiful, economic and practical, good anti-resistance effect, convenient construction and other excellent characteristics, at present, blade barbed wire has been widely used in many countries of industrial and mining enterprises, garden apartments, border posts, military fields, prisons, detention houses, government buildings and other countries of the security facilities.
Wire factory introduction annealing wire is widely used mainly because it has good elasticity and flexibility, in the process of annealing can be very good control of its soft and hard degree, it is mainly made of iron wire, more often used in the construction industry tied wire use. In the production of annealing wire will be processed according to the performance of the material, according to the demand for different degree of hardness of its soft change, can make it has more advantages, can reduce the consumption of metal, reduce the cost of production.
Hot dip galvanized wire 5#-28#, including 500-1000 kg large plate of hot dip galvanized wire. Our hot dip galvanized wire is made of national standard low carbon steel wire after drawing molding, pickling rust removal, high temperature annealing and other processes. The products have the characteristics of strong flexibility, good plasticity and so on. The zinc content can reach 360 g /m2, which is welcomed by customers. We can also provide various specifications of galvanized wire according to customer requirements. The PRODUCTS ARE WIDELY USED IN construction, HIGHWAY fence, TIE-flower, weaving and other industries, mainly used in the manufacture of wire mesh, nail making, highway barrier and construction engineering binding wire, etc. In the rolling process, if the surface of the steel wire is rough, the relative friction coefficient of the steel wire and roll increases, the friction resistance increases, the steel wire elongation decreases, the width increases. In the production of weighted leather material is easy to wide, is because of its rough surface. On the contrary, the surface of the steel wire is smooth, because the friction resistance between the steel wire and the roll is small, it is easy to extend, and the width is small. Domestic steel wire in order to prevent rust, the surface coated with butter, such as butter removal is not clean, easy to slip when rolled flat, also affect its width.Hot dip galvanized hexagonal net is made of low carbon steel wire by mechanized braided welding and then by hot dip zinc treatment. The net color is white and shiny, thick zinc layer, uniform mesh, flat mesh surface, solder joint tension resistance, high corrosion resistance. The surface of the steel wire is usually protected by hot-dip galvanizing, and the thickness of the galvanized protective layer can be made according to the requirements of customers. Hot-dip galvanizing hexagonal net is another kind of twisting mesh corresponding to the galvanizing hexagonal net.
A remarkable characteristic of stainless steel wire rope is its inherent corrosion resistance to concentrated nitric acid and dilute nitric acid, which makes it easy to be distinguished from most other metals or alloys. But high carbon 420 and 440 steel in the nitric acid point test is slightly corroded, non-ferrous metal encountered concentrated nitric acid is immediately corroded, and dilute nitric acid has strong corrosion on carbon steel.2. The cage must be strong
5, according to the wire diameter thickness to adjust zinc dipping time
Hot dip galvanizing, also known as hot dip galvanizing, is a method of obtaining a metal covering layer by immersing a steel member into a molten zinc solution. With the rapid development of high-voltage power transmission, transportation and communication, the protection requirements for steel parts are becoming higher and higher, and the demand for hot-dip galvanizing is also increasing. Usually the thickness of electrogalvanized layer is 5 ~ 15μm, and the large roll galvanized wire layer is generally more than 35μm, or even up to 200μm. Hot dip galvanized coating ability is good, dense coating, no organic inclusions.
The formation process of hot dip galvanized layer is the process of forming iron-zinc alloy between the iron matrix and the outside pure zinc layer. The surface of the workpiece forms the iron-zinc alloy layer during the hot dip plating, so that the iron and pure zinc layer is well combined. The process of large roll galvanized wire can be simply described as: when the iron workpiece is immersed in the molten zinc solution, the first zinc and α-iron (body-centered) solid melt is formed on the interface. This is a crystal formed by the matrix metal iron dissolved with zinc atoms in the solid state. The two metal atoms are fused with each other, and the gravitational attraction between the atoms is relatively small.
One is to do a good job of galvanized wire packaging, avoid bump, to ensure the integrity of the zinc layer;
In the atmosphere containing carbon dioxide and hydrogen sulfide and Marine atmosphere is not corrosion resistant, in high temperature and high humidity air and contain organic acid atmosphere is small, galvanized layer is also easy to be corroded. In order to make large rolls of galvanized wire on the surface of the deposited layer to the local, remove the surface film layer, surface inclusions and other defects can be found and treated by conventional techniques. Excess foam is caused by soaps and surfactant saponable fats brought into the tank, and moderate rates of foam formation may be harmless.