Therefore, the rust of galvanized black iron wire has a great relationship with storage. At the same time, after rust, it is also necessary to conduct reasonable post-processing to avoid affecting its use effect. Of course, when the black iron wire is galvanized, it is also necessary to ensure the thickness of the galvanized layer, so that it can also reduce the possibility of rust. Speaking of galvanized iron wire, perhaps many people think it is relatively rare, in fact, it is not.
2. Dissolution treatment: Put the pickling steel wire into the dissolution tank, and dissolve the zinc powder with the bath liquid by heating, and the dissolved zinc liquid will adhere to the surface of the steel wire.Customers do not need to worry about the impact of the production cycle when ordering products from the thorn rope factory, because the overall treatment is now focused on the waste gas, so the production of thorn rope should be said to have the least impact. Customers ordering products in the thorn rope factory can rest assured that the delivery time this piece, can provide customers with goods on time. If the production cycle is not affected, then customers will be more assured of the thorn rope factory.
Through drawing forming, pickling rust removal, high temperature annealing, hot dip galvanizing. Cooling process and other processing. Electric galvanized iron wire selection of high quality low carbon steel as raw material, after drawing, galvanizing and other processes completed. It has the characteristics of galvanized layer, strong corrosion resistance and strong galvanized layer, etc. Electric galvanized iron wire is widely used in construction, highway wall, tie-flower, net weaving and other industries.2. Eliminate caked zinc residue on zinc liquid surface
Hot dip galvanizing is to make the molten metal react with the iron matrix to produce an alloy layer, so that the matrix and the coating are combined. Hot dip galvanizing is to first pickling the iron and steel parts. In order to remove the iron oxide on the surface of the iron and steel parts, after pickling, it is cleaned in the tank of ammonium chloride or zinc chloride aqueous solution or mixed aqueous solution of ammonium chloride and zinc chloride, and then sent into the hot dip plating tank. Hot dip galvanizing has the advantages of uniform coating, strong adhesion and long service life.
1. After getting the bird cage, do not rush to use it. Clean the cage with a clean cloth or rubber. Then use fine yarn paper (do not use coarse sandpaper randomly), gently polish some parts that need to be polished again to improve the surface finish and trace, and pay attention to not damage the original bamboo green. After careful observation, use a razor blade to carefully clean the individual areas with small burrs.
There are three ways to twist the barbed rope: positive twist, reverse twist, positive and negative twist.
Features: Strong flexibility, good plasticity, a wide range of uses process: selection of high-quality low-carbon raw materials, after drawing, annealing processing, soft and strong tensile resistance. The finished product is coated with anti-rust oil, not easy to rust, can be bundled according to customer requirements, each bundle is 1-50kg, can also be made into U wire, broken wire, etc., plastic inside and linen outside packaging, mainly used for binding wire, construction wire, etc.
Large roll galvanized wire is made of low carbon steel wire rod processing, is made of low carbon steel, after drawing forming, pickling rust removal, high temperature annealing, hot dip galvanized. Cooling and other surface treatment process processing. Large roll galvanized wire is divided into hot dip galvanized wire and cold galvanized wire (electric galvanized wire). Although galvanized galvanized wire and silver powder paint spray effect appearance is not much different. But the effect is very different, galvanized wire surface is zinc layer, good adhesion, good corrosion resistance.
In the calculation process of 12*14 specifications of barbed rope, it can not be calculated according to the above calculation formula, because first of all, two specifications of raw materials are used, the thinner the wire diameter, the higher the processing cost. Generally speaking, a kilogram of 12*14 barbed rope can reach about 7.5 meters, and the ratio of warp wire to barbed rope cannot be calculated according to the traditional ratio of 7 to 3. The specific use of how much wire and silk need to go through a series of professional measurement but also increase the loss of raw materials and other factors to calculate. Thorn rope factory will also according to customer needs to calculate the reasonable amount of customer use.
The stainless steel barbed rope is made of stainless steel material after processing. The barbed rope has the characteristics of corrosion resistance and aging resistance. So why is the price of stainless steel barbed rope more expensive than ordinary barbed rope? Where do you want to go?
The front and back twist barbed wire costs less than 30 cents per meter, and the corresponding No. 12 hot-dip galvanized barbed wire costs 5 cents per meter. No matter in terms of service life, tensile strength, and anti-rust effect, it is no worse than No. 12 iron wire
Spray powder mainly acrylic powder, polyester powder and so on. Dipping is a kind of plastic coating process, that is, the plastic coating on the matrix, generally metal, such as: daily use of clothes hangers, pliers handles, scissors on the rubber sleeve, various handrails, etc. Plastic immersion is to heat the metal to spray plastic powder evenly on the metal to form a plastic film, or heat immersion liquid into the metal to cool it and then plastic coating on the metal surface.
Any application environment, users want a better the strength of the welded wire mesh, only need to improve its intensity, will make better the habit of using demand, but to be improved in the strength of this product, also need yo have a variety of conditions, will need to see factory in produce what kind of material, the strength of the product also is the material strength, But a manufacturer in the data does not fit the strength requirements, after all, there is no way to make the strength of the product progress, so this is the condition to.
During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.