Three is to do a good job in the production site of galvanized wire products clean and tidy, according to the scientific operation method to operate the production, the operator should wear the required dress. If it is hot dip galvanized wire products, we must do a good job of passivation treatment, will be able to effectively prevent discoloration, prolong the method of discoloration, can solve the problem of discoloration.
The anticorrosion of these raw materials is very different, and the use of life is not the same. Niu LAN net cold galvanized, also known as electroplating, galvanized quantity is very little, rust in rain, but the price is cheap, the use of life in 5-6 years. Hot dip galvanizing (low zinc and high zinc) on the amount of zinc in 60 grams to 400 grams, the service life is about 20-60 years, corrosion resistance is general.
In GENERAL, THE HARDNESS OF A METAL IS OFTEN CONSIDERED AS THE RESISTANCE OF a MATERIAL TO COMPRESSION PLASTIC deformation, scratches, wear, or cutting. In the adjustment of zinc dip distance of galvanized wire, keep the original speed unchanged, according to the time of zinc dip, wire diameter, and then estimate the zinc dip distance. By adjusting the zinc dipping distance, the zinc dipping time of various specifications of steel wire is shortened by 5s on average compared with that before debugging, so that the zinc consumption is reduced, the zinc consumption per ton of steel wire is reduced from the original 61kg to 59.4kg.
The entire steel surface is protected, and the melted zinc is easily coated evenly, whether in the interior of the pipe fitting in a depression, or in any other corner where the coating is difficult to access. The hardness of galvanized coating is greater than that of steel. The Eta layer of the upper layer of Z is only 70 DPN hardness, so it is easy to be dented by collisions. However, the hardness values of the lower layer of Zeta layer and delta layer are 179 and 211 DPN respectively, which are higher than that of the iron material of 159 DPN. Therefore, its impact resistance and wear resistance are quite good.
Different from the general zinc barbed rope, the zinc content of the surface of the high zinc barbed rope is very high, which can reach 6-8 times of the former, so that it has a great advantage in service life. Ordinary products begin to corrosion in three or five years, while the latter takes longer time to change. Stainless steel barbed rope is in the material aspect of protection so durability is also better, these two products are known for long service life, but is high in price.
Pet cage has many types, and selective is bigger, pet cages are generally made of wire, with better coarse, then at the bottom with a wheel base, such a simple pet basket was made, in the wheel at the bottom of the mount is for the convenience of the mobile, a pet cages should also adapt to the location of the production in addition to a door, It is convenient for feeding pets.
Cold galvanizing is also called electric galvanizing. It is the use of electrolytic equipment to remove oil, pickling, and then put the pipe into the solution of zinc salt, and connect the anode of the electrolytic equipment, place zinc plate on the opposite side of the pipe, and connect the positive pole of the electrolytic equipment to the power supply. A layer of zinc is deposited on the pipe fitting by directional movement of an electric current from the positive pole to the negative pole. Cold plated pipe fitting is processed before galvanizing.
Hexagonal mesh is also known as twisting mesh, thermal insulation net, soft edge net. It is made of single – layer mesh. Its mesh, mesh wire, galvanized and PVC film properties and the same as the cage. This product can be different shapes and sizes of the block stone into the alloy net to form a flexible whole, can be lifted, car, shipping to the designated place, the alloy net connected to each other into a larger whole, construction throwing convenient, fast, good economic performance.
According to the different requirements of the industry, different weights of alloy ingots are put in the smelting furnace according to the standard, such as weaving, Ming, paper, lang, silicon, etc., and the data out of this smelting is called gold ore iron. Iron has gray iron, white iron and the above-mentioned gold, they have different characteristics, so in the industry according to their different characteristics to transport and selection. For example, in gray iron, its carbon exists in iron ore in graphite condition, the crack is often gray, soft and strong, simple filtering, suitable for casting.
In the electroplating tank through the current unidirectional make zinc plating on the metal surface gradually, the production speed is slow, the coating is uniform, the thickness is thin, usually only 3-15 micron, the appearance is bright, smooth, beautiful, poor corrosion resistance, generally will rust in a few months. The production process of hot wire plating mainly includes: preparation of the original plate → pre-plating treatment → hot dip plating → post-plating treatment → finished product inspection, etc. According to custom often according to plating pretreatment method.
In our daily life, what we can bend with our hands is basically galvanized iron wire, not steel wire. It has a high zinc content, which ensures excellent toughness and resilience, as well as ultra-high corrosion resistance, which can be maintained in outdoor environments for decades. There are many practical galvanized iron wire, such as strong reliability, galvanized layer and iron together, forming a special metallurgical structure, in the use and transportation process, can ensure that it will not be mechanical damage.
Heavy duty hexagonal mesh made of steel wire by special machinery woven into a hexagonal mesh net. This kind of mesh can be cut and assembled into fence mesh, mountain hanging mesh, vegetation three-dimensional mesh, composite, etc. Aliases: Gabion mesh, heavy hexagonal mesh, ecological mesh, wire mesh, etc.