Wire mesh first welding after galvanized is through the end of welding and then the company to produce wire mesh wire mesh steel mesh construction mesh, floor heating mesh galvanized or hot dip galvanized. First galvanized after welding is to change wire mesh, after the end of welding can see the solder joint; The two processes are different in price. The cost of plating after welding is low, the appearance is smooth, and the cost of plating after welding is high, and it is not easy to rust.
The main customers of the thorn rope factory are still targeted at farms and plantations, because the demand for thorn rope is often very large.
Hexagonal mesh is also known as twisting mesh, thermal insulation net, soft edge net. It is made of single – layer mesh. Its mesh, mesh wire, galvanized and PVC film properties and the same as the cage. This product can be different shapes and sizes of the block stone into the alloy net to form a flexible whole, through lifting, car, shipping to the place, the alloy net connected to each other into a larger whole, construction throwing convenient, fast, good economic performance.Blade barbed rope production links need to be many times before the finished product, roughly down to four or five links.
In the atmosphere containing carbon dioxide and hydrogen sulfide and Marine atmosphere is not corrosion resistant, in high temperature and high humidity air and contain organic acid atmosphere is small, galvanized layer is also easy to be corroded. In order to make large rolls of galvanized wire on the surface of the deposited layer to the local, remove the surface film layer, surface inclusions and other defects can be found and treated by conventional techniques. Excess foam is caused by soaps and surfactant saponable fats brought into the tank, and moderate rates of foam formation may be harmless.
There is also a straight blade stabbing rope, which is mainly because the board and wire are not wound in the process of wrapping, so the blade stabbing rope produced is a straight product. The length of the barbed rope of this specification cannot be too long due to the limitation of logistics, and it cannot be bent because it is easy to be deformed by force. This is also the main reason why the barbed rope of the straight blade is not whole or long. Customers are advised to determine the spacing before purchase to prevent losses caused by no calculation.
That said, it can always deform by pulling hard without changing its integrity, so cold drawing has usually reached a limit, which is not a problem, because without this property it increases hardness, which is the desired effect. Cold wire drawing encountered more rain, when the climate is wet, easy oxidation and rust. Therefore, in the storage process should pay attention to avoid rust.
In the process of composite electroplating galvanized wire, the plating solution must be stirred to obtain the composite coating in which the particles dispersed in the matrix metal. Stirring methods include mechanical stirring, air stirring, ultrasonic stirring, bath circulation, etc. The acid activation solution in the production process can remove the corrosion products and oxide film on the surface of the low carbon steel wire without excessive corrosion on the matrix.
Hook flower net is made of silk hook, the mesh is uniform, flat net surface, beautiful generous net width, wire diameter is thick, not easy to corrode long life, weaving succinct, beautiful and useful. Widely used for raising chickens, ducks, geese, rabbits and zoo enclosures. Mechanical equipment protection, highway guardrail, sports venues fence, road beautification belt protection network. After the screen is made into a box-like container, it can be used to maintain and support the seawall, hillside, road and bridge, reservoir and other civil engineering.
When the barbed rope is installed in different places, the choice of barbed rope column is different. Usually, the barbed rope column we install is cement column, but the use of cement column also has its drawbacks. For example, it’s not so convenient if we install it on a steep hill where transportation is not very convenient. This time can use barbed rope with the composite column to install.As we all know, the purpose of painting the fence fence factory is to make the product better anti-corrosion effect. So what should we pay attention to in the product painting?
For the wide use of screen, the state has regulations. You also specify the diameter size, mesh size, or usage method. For plastering mesh, mesh should be less than 20 and diameter greater than 1 nm. Not only are specifications specified, but safety is preferred if wire mesh is used in exterior plastering mesh. If you fall, the consequences are unimaginable. Therefore, the application of norms should be combined with reality.
If the surface of galvanized wire is black and the galvanized layer is thin and uneven, the galvanized wire is partly because the inventory storage time is longer, but also because the production technical requirements of galvanized wire do not meet the standard and lead to the quality problems of galvanized wire. According to the use of galvanized wire is different, galvanized wire has soft and hard, then the galvanized wire used for binding requires the flexibility of galvanized wire is better, the flexibility of galvanized wire is good, and it can be easy for workers to operate.
After the wire mesh appears black spots, you can choose the appearance of treatment to deal with this problem, such as galvanized, paint, dip plastic to deal with, after the appearance of the welding mesh surface smooth and bright, beautiful and generous. Before wall plastering, the wall column is connected to the gap construction wire mesh, which can play a certain strengthening and heat preservation effect. The mesh is hung on the interface surface of different grassroots, and the length of each side should meet the requirements of 100mm, so as to prevent shrinkage and cracking caused by different grassroots. Mesh wire diameter can also determine the effect and efficiency of construction, mesh fine laid up convenient soft, high construction efficiency; Of national standard can assure quality, but laid respect is inferior to fine construction fast.Three methods of twisting the thorn rope: forward twisting, reverse twisting, reverse twisting.
Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.
Hook mesh is crocheted with silk heart, its mesh is uniform, flat net surface, beautiful and generous net width, thick silk diameter, not easy to corroded long life, weaving simple, beautiful and useful. Widely used for raising chickens, ducks, geese, rabbits and zoo enclosures. Protection of mechanical equipment, highway guardrail, sports site fence, road beautification with protective net. The screen in the manufacture of a box-like container, with stone filled with the cage, can be used to maintain and support seawall, hillside, road and bridge, reservoir and other civil engineering.
Hexagonal cage has a wide range of applications, with the progress of science and technology, has been extended to the major hydraulic, civil engineering. Geotechnical engineering and other projects. In hydraulic hexagonal cage in river construction from closed utility, think appropriate and the use of hexagonal cage to fill stone, fixed river, can be used to avoid river erosion brought water and soil loss. In civil engineering projects, hexagonal cage that is suitable and the use of similar particle size volume particles to fill, mesh wall is formed between the cage, which is the stone cage retaining wall. Of course, the quality of any kind of product is also affected by the implementation of the specification of the manufacturer, if it is the welding screen manufacturers in the production of their own is not very high implementation of the specification, or in the production line of the procedure specification has declined, or there is no higher requirements on the production link.The difference is that hot dip galvanizing is dipped in zinc solution melted by heating, which has fast production speed and thick but uneven coating. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust.