. For instance, the growing need for eco-friendly solutions in the construction industry has led to an increased demand for anatase-based photocatalytic coatings that can help reduce air pollution. Similarly, the development of new technologies like perovskite solar cells has opened up new opportunities for anatase, further driving up its demand and price.
The reaction liquid is filtered through plate and frame pressure to obtain lithopone in the form of a filter cake with a moisture content of no more than 45%. It is then roasted in a drying furnace to change the crystal form of lithopone, and is then pickled with sulfuric acid at a temperature of 80°C. Finally, it is washed with water, reinforced with colorants, filtered, dried and ground into powder.
The basic scenario of resistive switching in TiO2 (Jameson et al., 2007) assumes the formation and electromigration of oxygen vacancies between the electrodes (Baiatu et al., 1990), so that the distribution of concomitant n-type conductivity (Janotti et al., 2010) across the volume can eventually be controlled by an external electric bias, as schematically shown in Figure 1B. Direct observations with transmission electron microscopy (TEM) revealed more complex electroforming processes in TiO2 thin films. In one of the studies, a continuous Pt filament between the electrodes was observed in a planar Pt/TiO2/Pt memristor (Jang et al., 2016). As illustrated in Figure 1C, the corresponding switching mechanism was suggested as the formation of a conductive nanofilament with a high concentration of ionized oxygen vacancies and correspondingly reduced Ti3+ ions. These ions induce detachment and migration of Pt atoms from the electrode via strong metal–support interactions (Tauster, 1987). Another TEM investigation of a conductive TiO2 nanofilament revealed it to be a Magnéli phase TinO2n−1 (Kwon et al., 2010). Supposedly, its formation results from an increase in the concentrations of oxygen vacancies within a local nanoregion above their thermodynamically stable limit. This scenario is schematically shown in Figure 1D. Other hypothesized point defect mechanisms involve a contribution of cation and anion interstitials, although their behavior has been studied more in tantalum oxide (Wedig et al., 2015; Kumar et al., 2016). The plausible origins and mechanisms of memristive switching have been comprehensively reviewed in topical publications devoted to metal oxide memristors (Yang et al., 2008; Waser et al., 2009; Ielmini, 2016) as well as TiO2 (Jeong et al., 2011; Szot et al., 2011; Acharyya et al., 2014). The resistive switching mechanisms in memristive materials are regularly revisited and updated in the themed review publications (Sun et al., 2019; Wang et al., 2020).
In the meantime, the chemical factories of Continental Europe, principally in Germany, Austria and Belgium, had taken hold of the novelty and under the collective name of lithopone or lithophone, by numerous processes, produced various grades of the pigment, branding the respective qualities as red seal, green seal, yellow seal, blue seal, etc., or selling them under some fancy name. Of this we shall speak later on. The crusade against the use of white lead in the various countries of Continental Europe, assisted the manufacturers, to a very great extent, in marketing their products, not only to industrial concerns, as has been the case in this country, until recently, but to the general painting trade. Up to 1889 the imports into this country were comparatively small. At that time one of the largest concerns manufacturing oilcloth and linoleum in the State of New Jersey began to import and use Charlton white. Shortly after that other oilcloth manufacturers followed suit, replacing zinc white with lithopone in the making of white tablecloth, etc., and later on abandoning the use of white lead in floor cloth and linoleum. This gave an impetus to several chemical concerns, that erected plants and began to manufacture the pigment. Competition among the manufacturers and the activity of the importers induced other industries to experiment with lithopone, and the shade cloth makers, who formerly used white lead chiefly, are now among the largest consumers. Makers of India rubber goods, implement makers and paint manufacturers are also consumers of great quantities, and the demand is very much on the increase, as the nature of the pigment is becoming better understood and its defects brought under control. Large quantities find their way into floor paints, machinery paints, implement paints and enamel paints, while the flat wall paints that have of late come into such extensive use owe their existence to the use of lithopone in their makeup.