When the large roll galvanized wire galvanizing process coating foaming, first check the bath temperature. If the bath temperature is not low, then strengthen the plating before removing oil, prevent the matrix metal in acid corrosion. If you pay attention to these problems, the foaming phenomenon still exists, it should pay attention to the amount and quality of additives, then you can stop adding additives, with high current electrolysis for a period of time, in order to reduce the content of additives, observe whether the foaming phenomenon is improved. If there is still no improvement, it is necessary to check whether the storage period of additives is too long, or whether there are too many impurities in the additives.
In the electroplating tank through the current unidirectional make zinc plating on the metal surface gradually, the production speed is slow, the coating is uniform, the thickness is thin, usually only 3-15 micron, the appearance is bright, smooth, beautiful, poor corrosion resistance, generally will rust in a few months. The production process of hot wire plating mainly includes: preparation of the original plate → pre-plating treatment → hot dip plating → post-plating treatment → finished product inspection, etc. According to custom often according to plating pretreatment method.
Secondly, the zinc-iron alloy protective layer of hot-dip galvanized wire has self-healing properties. When the surface of hot-dip galvanized wire is damaged or scratched, zinc metal can form zinc ions through electrochemical reaction, self-healing repair of the damaged zinc-iron alloy protective layer, so as to maintain the corrosion resistance of the steel wire. This self-healing property enables the hot-dip galvanized wire to be quickly repaired during use, even if there is a slight scratch or damage on the surface, avoiding further corrosion. After the ordinary steel wire is damaged on the surface, it is often unable to repair itself, which is easy to lead to the diffusion of corrosion and accelerate the aging and damage of the steel wire.
Hot dip galvanizing is then oiled and chromed. The quality of hot-galvanized sheet produced by this method is significantly improved compared with that by wet galvanizing method. It is only valuable for small-scale production. Continuous galvanizing production line includes a series of pretreatment procedures, such as alkali degreasing, hydrochloric acid pickling, water washing, solvent coating, drying, etc., and the original plate needs to be annealed in cover furnace before entering the galvanizing line.
When galvanized wire out of the light plating should be carried out light treatment. The bath temperature of galvanized wire should be controlled well. Galvanized wire, also known as hot dip zinc and hot dip galvanized, is an effective way of metal corrosion prevention, mainly used in various industries of metal structure facilities. It is to immerse the steel parts after rust removal into the molten zinc liquid at about 500℃, so that the surface of the steel member is attached with zinc layer, so as to play the purpose of anticorrosion.
Hook mesh is crocheted with silk heart, its mesh is uniform, flat net surface, beautiful and generous net width, thick silk diameter, not easy to corroded long life, weaving simple, beautiful and useful. Widely used for raising chickens, ducks, geese, rabbits and zoo enclosures. Protection of mechanical equipment, highway guardrail, sports site fence, road beautification with protective net. The screen in the manufacture of a box-like container, with stone filled with the cage, can be used to maintain and support seawall, hillside, road and bridge, reservoir and other civil engineering.
For the specification of galvanized wire, the galvanized wire produced by our factory can range from No.8 to No.22, which refers to the BWG standard, that is, from about 4mm to 0.7mm, which can basically cover the type required by customers. As for the raw material of galvanized wire, normally, we use Q195 mild steel, and some factories will also use SAE1006 or SAE1008. The following is the zinc coating, for galvanized wire, this thing is more important, the general zinc coating is about 50g/m2 to 80g/m2, some customers need high zinc galvanized wire, zinc coating can reach 200g/m2 to 360g/m2. The tensile strength of galvanized wire is usually 350n/m2 to 800n/m2. Then there is the packaging specification of galvanized wire. The specifications of small rolls of galvanized wire are 50kg/ roll, 100kg/ roll and 200kg/ roll. Of course, there are large rolls of galvanized silk, the weight can reach 300kg/ roll or 800kg/ roll.
Carbon spring steel wire should have high tensile strength, elastic limit, endurance and fatigue strength, and impact and vibration resistance. To ensure the strength and endurance index, especially to avoid changing the occurrence of cracks, is the key to produce spring steel wire. The inner quality and surface quality of the wire rod directly affect the function of the wire.