The derusting steel parts are immersed in the melted zinc liquid at about 500℃, so that the surface of the steel member is attached with zinc layer, so as to achieve the purpose of anti-corrosion. The surface of galvanized wire coating can see whether the quality of galvanized wire is good or not. If the strength of zinc attached to the wire is very poor, then this galvanized wire do not buy, because this galvanized wire must be poor galvanized wire.
Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust. Compared with electrogalvanizing, hot galvanizing has lower production cost and less impact on the environment than electroplating.
National standards on the use of wire mesh standards have certain requirements, diameter and mesh size matching use, rather than simply diameter, on the plaster layer to use the mesh should not be greater than 20×20, diameter is not easy to be less than 1mm, just choose diameter is not much meaning, choose 40×40×0.9 and choose 10×10×0.6 wire mesh, Which is better? I’m afraid it’s 10 by 10 by 0.6.
Electrode application range is wide, can realize a variety of materials, a variety of profiles and a variety of joint forms of welding. (1) Welding between low carbon steel, low alloy steel, medium carbon steel, alloy steel and other metal materials or dissimilar metal materials can be achieved. The weld has good comprehensive mechanical properties, and the tensile strength can reach more than 400MPa. ⑵ Can realize the welding of large plate, steel frame, plate – tube, rod – rod, tube – tube and other profiles. ⑶, can realize docking, Angle, lap, T joint and other joint forms of welding. ⑷ mainly suitable for flat welding.(5) it can surfacing the parts of wear failure, so as to obtain the surface surfacing layer with melting depth, smooth surface and excellent performance. ⑹ It can be realized that no bevel 1 ~ 6mm thick metal sheet single-side welding double-side molding.
There are many production links of blade barbed rope, and the finished product can only be produced after several times of production. Roughly, there are four or five links.
Hexagonal mesh is made of galvanized iron wire woven by automatic mesh machine, mesh into regular hexagonal, mesh standard, beautiful, mesh size can be customized according to customer requirements, usually 27mm,20mm, 13mm, wire diameter from 0.40mm to 1.20mm, to meet the requirements of different customers.
Blade thorn rope because the volume is relatively large so thorn rope factory is used to packaging treatment.
At the time of production, the annealing wire will be processed according to the performance of the material. According to different needs, the degree of hardness and softness can be changed, which can make it have more advantages, reduce the consumption of metal and reduce the cost of production. In the use of the time does not need to carry out daily maintenance and maintenance, not only can save a lot of time, but also can reduce the cost, but also has good stability, strong corrosion resistance, greatly extend the service life. Another way is to have special equipment for measuring, which is expensive and impossible for ordinary users to buy. The last method is that there is a hierarchy gap in the light sense of the barbed rope, the general zinc barbed rope is more bright and the high zinc barbed rope is slightly darker, so customers do not think that the more beautiful the appearance of the product is good quality.After annealing, the wire will become soft, flexibility will increase, iron is a relatively active metal, and more active than hydrogen, so it is a good reducing agent. At room temperature, iron in the dry air is not easy to react with oxygen, sulfur, chlorine and other non-metallic elements, its production cost is lower, use and scale is wider, better protection function, so it is an important material for iron and steel parts in a strict working environment.
The distance between the adjacent two thorn rope installation do not know whether you have noticed? Careful observation can find that its spacing is not the same, the thorn rope factory for customer consultation when asking the installation height of the reason.
The wire after the first plating, its strength limit is also higher than the first plating, plated zinc and then made of wire not only toughness and high strength. There is a lower figure in the strength limit of galvanized iron wire because of the quality of zinc, because the strength of zinc technology is several times smaller than the wire itself. It is difficult to hot-dip galvanize drawn wires, and it is impossible for finer and very fine wires to be coated with the desired thickness of smooth zinc. Because of its light weight, strength is relatively large has gradually begun to replace the original column. At the same time, due to the relatively uniform specifications, the barbed rope installation is also more beautiful. The direct spacing of the barbed rope is relatively fixed, which can effectively prevent crossing. At the same time, the mesh at the bottom is relatively dense, while the mesh at the top is relatively loose, which can save resources. Cages are more often used for large dogs, which are very powerful. So choose a dog cage must be strong, otherwise the dog can easily break the cage and escape.Its specific design layout principle is:
The production process of stainless steel blade and galvanized blade is basically similar. The blade size is usually determined according to the mold.
The most common barbed rope is 14*14 and 12*14 wire diameter barbed rope. The 14*14 wire diameter barbed rope is made of 200mm galvanized wire, and the barbed distance can be directly adjusted from 8-12cm. According to the different needs of each customer processing customized. Similarly, the length of each bundle of barbed rope can be cut from 50-250m as required. The 12*14 standard barbed rope is twisted by two different specifications of galvanized wire for 260mm and 220mm barbed wire. Other parameters are roughly the same except for different wire diameters. The price is slightly expensive because the latter uses more materials.
Cold galvanizing (galvanizing) is in the plating tank after the current unidirectional, so that the zinc gradually plated on the metal surface, slow production speed, uniform coating, thin thickness, usually as long as 3-15g, bright appearance, poor corrosion resistance, usually a few months will rust. Compared with hot dip galvanizing, the production cost of electric galvanizing is lower.
I’m going to take the middle one. Steel wire galvanized is very important, must master galvanized, galvanized, because there are many methods, but we first must choose hot plate, welding mesh material, and then excitation, and diameter of steel wire is mainly according to the construction requirements, as well as the requirements of the range of application.And high-quality data are constrained by production costs and production conditions, so some electric welding mesh manufacturers do not meet this requirement, in this case, there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.
With the development of mining industry, the classification of pig iron is already very broad in our country, which can satisfy the demand of mechanical industry. In general, the iron used to produce large rolls of galvanized wire can be divided into two classes. A metal exercised directly from the iron ore through the iron making stroke, the composition of the ore is iron oxide, silica and other miscellaneous stones. When this ore is specially refined into metal iron, carbon, silicon, manganese, and other elements are mixed into it. The material produced in this way is called ordinary pig iron, which is also the material for the first grade.