Electric galvanized wire direct selling is in the plating tank through the current one-way to gradually zinc plating on the metal appearance, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust. Compared with hot dip galvanizing, the production cost of electric galvanizing is lower. The difference between cold galvanizing and hot galvanizing: the difference between cold galvanizing and hot galvanizing is that the amount of zinc is different. They can be identified from the color. The color of cold galvanizing is shiny silver white with yellow. Hot dip galvanizing shiny white.
Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.
The production process of large rolls of galvanized wire is a level of drawing, through the mold into a slightly smaller diameter than the original. And so on down to the desired length. One pull is not desirable, must be numbered, from coarse to fine is dependent on metal ductility. If it changes too much it just breaks. After drawing to a certain diameter, galvanized, so that the finished product.
Generally, due to wet weather and more precipitation, oxidation and rust of binding iron wire NetEase occurs, so we should better store and use galvanized iron wire to avoid rust as far as possible. About the barbed wire, the surface of the barbed wire attached a layer of galvanized layer, the galvanized layer if too thick will not meet the SGS environmental standards. But if it is too thin, it is easy to oxidize with water molecules and rust.
Hot dip galvanized welding mesh is made of iron wire, processed by precision automatic mechanical technology. The mesh surface is smooth, the structure is strong, and the integrity is strong. Even if the local cutting or local pressure is not relaxed, the hot dip zinc is processed. Hot dip galvanized welding mesh surface white color, thick zinc layer, high zinc content at the solder joint, uniform mesh, flat mesh surface, solder joint tensile resistance, high corrosion resistance. It has the advantages that ordinary barbed wire does not have.
After the corrosion of impregnated hexagonal wire mesh, the original characteristics will be lost, and the shape, color and mechanical properties will be changed, resulting in equipment damage, pipeline leakage, etc., specifically, it is easy to break and lose the original protection function. Usually, there are three kinds of metal corrosion: physical corrosion, chemical corrosion, electrochemical corrosion, corrosion in addition to the chemical properties and organizational structure of the metal itself, but also related to the surrounding medium, such as wet environment is easier to rust than dry environment, more impurities than impurities less easy corrosion, high temperature conditions than low temperature conditions easy corrosion. After understanding these, we can effectively prevent the corrosion of impregnated six-sided wire mesh, prolong the service life of the product.
If the coating roughness is not caused by the above reasons, it may be caused by impurities in the plating solution. Can take a small amount of electroplating solution, after filtration test, then take a small amount of electroplating solution, after zinc powder treatment test, check the problem is caused by solid particles or copper, lead and other foreign metal impurities. Test them one by one and it’s not hard to find the cause of the problem. Galvanized iron wire coating foaming, binding force is not good.
Hook mesh is hooked flower machine (diamond mesh machine) for all kinds of metal hooks, can be divided into (lock, twist folding locked two. Data
VC wire, stainless steel wire, low carbon steel wire, wire, galvanized wire. Based on entry, rhomboid net, rhomboid net, ring collection, chain net, collection, anchor net, hook breeding, playing net fence. Appearance disposal: according to electric galvanizing, hot dip galvanizing, plastic hook polyethylene plastic bag, dip plastic, spray plastic, hook mesh. According to the use: decorative hook (simple, guardrail, hook mesh, maintenance of another classification: stainless steel data 201,302,304 hook (left, 316, appearance disposal, none).
Large roll galvanized wire is like the literal meaning, is wrapped in a layer of zinc on the surface of low carbon steel wire material, beautify the appearance at the same time, but also improve the corrosion resistance of galvanized wire. Zinc dissolves easily in acids and alkalis, so it is called a dissoluble metal. Zinc changes little in dry air. In moist air, a dense basic zinc carbonate film forms on the surface of zinc.
The purchase of blade barbed rope also needs to consider the higher manual installation cost in the later period. Generally, customers only ask the price of blade barbed rope, and sometimes the installation cost is not taken into account in the budget, which is very unreasonable. Because the installation cost is not cheaper than the rope itself, sometimes even the blade rope and column combined. The blade stabbing rope needs a lot of manpower and material resources for installation. In general, the installation cost is also a relatively large expenditure item in the stabbing rope project.