When the large roll galvanized wire galvanizing process coating foaming, first check the bath temperature. If the bath temperature is not low, then strengthen the plating before removing oil, prevent the matrix metal in acid corrosion. If you pay attention to these problems, the foaming phenomenon still exists, it should pay attention to the amount and quality of additives, then you can stop adding additives, with high current electrolysis for a period of time, in order to reduce the content of additives, observe whether the foaming phenomenon is improved. If there is still no improvement, it is necessary to check whether the storage period of additives is too long, or whether there are too many impurities in the additives.
Use in daily life does not need to carry out maintenance and maintenance, save a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. More kinds, can be selected according to different uses, making annealing wire device is simple, improve the utilization rate of the device. The material properties of annealed wire can meet different processing requirements.On the highway, barbed rope protection net is generally to prevent people and animals from crossing the highway at will, so as not to interfere with driving and reduce accidents, as well as effectively prevent illegal occupation of road land and other issues of traffic safety facilities. There are many forms of barbed rope protective nets, commonly used metal, woven net, barbed wire and often green gracilaria. Metal braided net is set in crowded areas, barbed wire is used in areas with few people and animals, and the structure of hedges and barbed wire is used in toll stations and service areas. In the past two years, considering the beauty of the problem, in the Pearl River Delta region of some highways with fruit plastic spot welding network (usually said guardrail network), this barbed rope protection network is more good-looking, durable, the overall effect is good, but the construction requirements are higher, more expensive. General sections should not be used, in the city center, scenic spots or strong requirements for beautiful sections can be used.
3, barbed rope protection net in the bridge, channel, should be toward the bridge head cone slope (or end wall) direction surrounded, should not leave for people, livestock can drill into the gap.6, passivation to remove hydrogen parts should be passivation after the removal of hydrogen, passivation before the application of 1%H2SO4 or 1% hydrochloric acid activation 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.
Widely used in practice, iron wire also has certain harm, simple rust and corrosion, so we can generally use galvanized method to prevent product corrosion. Together in addition to this method, metal commonly used treatment methods and phosphating treatment, oxidation treatment, etc. Metal phosphating treatment: iron and steel products to remove oil, rust, into the specific composition of the salt solution soak, you can form a layer of water soluble salt film on the surface of the metal, this process is called phosphating treatment.
Quality standard: Zinc content per square meter has reached or exceeded 122g.The production process of large rolls of galvanized wire is a level of drawing, through the mold into a slightly smaller diameter than the original. And so on down to the desired length. One pull is not desirable, must be numbered, from coarse to fine is dependent on metal ductility. If it changes too much it just breaks. After drawing to a certain diameter, galvanized, so that the finished product.
When using these two products, it is obvious that there is a gap between them. By pulling or bending the wire, it is often difficult to restore the original, for example, if the same place is repeatedly bent, it will be found that it has broken, and the cold drawing wire will not. Cold drawing wire compared with iron wire, its hardness, tensile resistance, bending ability is greatly enhanced, suitable for building materials.
3. Put zinc block into the plating aid pool regularly, so that the bivalent iron in the plating aid becomes trivalent iron, and it is an important measure to stabilize the PH value in a numerical range. At the same time, it is convenient for the filter to filter out the trivalent iron ions in the plating aid; Ferric ion is controlled between 0.3 and 1.0g/L; When hydrogen is not released in the plating aid, the zinc block is continued. It is an effective measure to reduce zinc slag, improve the fluidity of zinc liquid and reduce the thickness of zinc layer to play the role of plating aid filter.
When laying steel wire mesh, according to the laying method from the middle to both sides in turn. Wall plastering engineering use wire mesh material is generally two kinds: one is electroplating, the other is hot dip galvanized. The former has low cost and a wide range of use. The cost of hot-dip galvanized material is slightly higher than that of electroplating, and the cost is high and the life is good to prevent rust. Hot dip galvanizing is in the case of heating plating. After the zinc is melted into liquid form, the base metal is immersed in it so that the zinc interpenetrates with the base metal and binds so tightly that there are no other impurities or defects left in the process.
3. Salt water or alkali washing: In order to remove the residual acid in the dissolution tank, it is necessary to carry out salt water or alkali washing treatment on the steel wire to ensure that the surface of the steel wire is clean.
The characteristics of hexagonal wire mesh: strong structure, flat surface, with good corrosion resistance, oxidation resistance and so on.